Differences

This shows you the differences between two versions of the page.

--- speakerphone [2024.02.07 13:48] – created Steve Isenberg
+++ speakerphone [2024.02.11 12:42] (current) – Steve Isenberg
@@ Line 1: / Line 1: @@
-=====Speakerphone Info=====
+~~NOCACHE~~ <fc #a0a0a0><fs small>This page last changed ~~LASTMOD~~ Visits: [{{counter|today| time| times}} today, {{counter|yesterday| time| times}} yesterday, and {{counter|total| time| total times}}]</fs></fc>\\
-====PolySync 40====
+======Speakerphone Info======
+====PolySync 40=====
 (Thanks to BK)
-When you receive the pair of PolySync 40 Speakerphones, download the associated management utility to update the Firmware.
+=====Using two 40's in a meeting=====
+Assuming you have charged them up.
-Setting them up in tandem.
+  - Turn on both 40's (see: power button on narrow side, button on the right)
-  - Follow instructions to pair the two speakerphones
+  - Both will tell you they're powered up and the state of the battery.
-  - Then after they're paired, plug one into the USB port
+  - Press and hold for a couple of seconds the Link button {{lctg:polysync40_linkbutton.png}} on both 40's (see: link button on narrow side, button on left)
-  - Test the mic and speaker functions via Zoom preferences
+  - Hear “connection successful” and LED flashes white on both speakerphones means linking is successful.
-Usage, based on LCC room 237
+Now, you need to connect one of the 40's to the computer in the room that'll be connected for the audience.  Call this "Audience PC".
-  * Position one of the units near the main presenter.  This is the USB connected device.
+  * If Audience PC has Bluetooth:
+    * Put Audience PC into Bluetooth search mode
+    * Go to one of the 40's and press the Bluetooth icon on top of the unit (left side)
+    * Make sure Audience PC sees the 40 and connect to it.
+  * If Audience PC does not have Bluetooth
+    * Using the intrinsic cable on the 40, connect to USB on the Audience PC.
+The speakerphones are now set and ready to be used for both microphone and audio speaker.
+  * Tell the Audience PC to use the PolySync 40 as its speaker
+  * Start Zoom and tell Zoom to use the PolySync 40 as its microphone
+Viola, you're all set.
+====Usage in a conference room====
+  * Position one of the units near the main presenter.  This is the USB connected device or the one paired with the audience PC.
   * Put the other in the middle of the audience seating area.  This can easily be picked up and moved around to be closer to any audience speaker.
+  * Make sure that both speakerphones are aligned so that they are parallel to the front of the room and parallel to each other.
+====Tips/Tricks====
+  * When moving a unit, hold it by the edges.  This way you will avoid pushing any of the buttons which might mute the mic or change the speaker volume.
+  * A charge should last for many hours longer than any meeting.  It's wise to charge them up after a meeting.
+=====Other information=====
+===Poly Lens App===
+Needed to update and customize.
+The "official" app download page doesn't work.  Here is the
+[[https://www.hp.com/us-en/poly/software-and-services/software/poly-lens/app.html|link to the working download page]]
+===User Manual Notes===
+Pertinent info from the Polysync 40 user manual [[https://www.poly.com/content/dam/www/products/phones/sync/sync-40/doc/poly-sync40-ug-en.pdf|download it]]
+{{lctg:polysync40_buttons.png?400}}
+====LEDs====
+|Crossing blue pattern|Pairing mode|
+|Solid blue|Pairing successful (connected)|
+|Flashing green|Incoming call|
+|Solid green|In a call|
+|Solid red|Mute active|
+|Crossing white pattern|Linking mode (daisy chain audio)|
+|Two white blinks|Linking successful|
+===Battery status===
+|solid white long bar|battery full|
+|solid white medium bar|battery high|
+|solid white short bar|battery medium|
+|solid red|battery low|
+|red flashes|battery critical|
+When in standby mode, no LEDs illuminate\\
+Need 5 hours for full charge
+===Link Speakerphones - Daisy chain audio===
+Make sure both speakerphones are updated to latest release in Poly Lens Desktop App.
+  - Pair or connect one speakerphone to your PC or mobile device.
+  - Press both Link {{lctg:polysync40_linkbutton.png}} buttons for 2 seconds.  Hear "connecting" and LEDs pulse white.
+  - Hear "connection successful" and LED flashes white on both speakerphones means linking is successful.
+  - Control system from either speakerphone
+  - End linking by pressing both Link {{lctg:polysync40_linkbutton.png}} buttons for 2 seconds, hear "device disconnected"